LexRides Forum Index LexRides
Lexington's Bike Forum
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Painting your bike
Goto page 1, 2  Next
 
Post new topic   Reply to topic    LexRides Forum Index -> Mechanical Questions
View previous topic :: View next topic  
Author Message
mcrib
townie
townie


Joined: 24 Oct 2007
Posts: 232
Location: 40502

PostPosted: Wed Nov 21, 2007 3:07 pm    Post subject: Painting your bike Reply with quote

Trish wants and new paint job on her bike and what the lady wants the lady gets I was wondering what advice I could get from all you internet users out there.
_________________
Albert Einstein trembled when he found out time was water. Seeping through the rafters to put out this burning world.
Back to top
View user's profile Send private message Send e-mail
brokebike
cutter
cutter


Joined: 21 Oct 2007
Posts: 2434
Location: local

PostPosted: Wed Nov 21, 2007 11:01 pm    Post subject: Reply with quote

I've painted a couple of bikes... you can get really good results with just spray cans as long as you have patience and do it right.

I'd recommend rough sanding the old paint without removing it... let that be your base primer layer. That old paint (especially if it is original to the bike) is going to be your most durable layer, so you might as well keep it on there.

Get some actual metal primer and go over the bike with a couple of coats. When you're ready for your final color, just do very light coats, and wet-sand in between each coat. I'd say, 3-4 coats. You can get wet sand paper at any auto supply store, or auto paint store. Wet sanding is important in getting that really smooth finish... otherwise it will most likely turn out all rough and "orange peel-ish" like spray paint usually does.
Back to top
View user's profile Send private message
mcrib
townie
townie


Joined: 24 Oct 2007
Posts: 232
Location: 40502

PostPosted: Thu Nov 22, 2007 2:31 pm    Post subject: Reply with quote

some of the stuff I have read suggested taking off all the original paint and then put primer on but I'm not sure.
_________________
Albert Einstein trembled when he found out time was water. Seeping through the rafters to put out this burning world.
Back to top
View user's profile Send private message Send e-mail
DHB
hipster
hipster


Joined: 28 Oct 2007
Posts: 71
Location: I'm not here, I'm over there.

PostPosted: Thu Nov 22, 2007 7:45 pm    Post subject: Reply with quote

I need some frames painted too, but I was thinking about trying powder coating. I've tried spray painting frames, but it looked like shit (probably because I didn't do it right) and it wasn't very durable (again, probably because I didn't do it right). I've heard that powder coating is cheap, but that's probably relative. I do know that it's durable though.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Burch
training wheels
training wheels


Joined: 09 Nov 2007
Posts: 10

PostPosted: Thu Nov 22, 2007 8:04 pm    Post subject: Reply with quote

I had a bike powder coated (the british green Schwinn Ross now has at the Icehouse, I'm sure most have seen it there). I thought it looked fucking beautiful. It was like 80 bucks or so. And the place is right around the corner from your house, Drew.
Back to top
View user's profile Send private message
DHB
hipster
hipster


Joined: 28 Oct 2007
Posts: 71
Location: I'm not here, I'm over there.

PostPosted: Thu Nov 22, 2007 8:16 pm    Post subject: Reply with quote

That's no too bad. do you remember the name of the place?
Back to top
View user's profile Send private message Send e-mail Visit poster's website
catamount
townie
townie


Joined: 21 Oct 2007
Posts: 163
Location: lex

PostPosted: Thu Nov 22, 2007 8:44 pm    Post subject: Reply with quote

I believe the place Will is speaking of is Metal Cleaners -920 National Ave
(859) 255-3700 - There are some things to consider if you go with powder coating. They quoted me $80-$110 earlier this year - it depends on who you talk to - one guy was a grump who did not seem like he wanted to deal with it thus the higher price and the other guy was super nice. I think some folks know of other powder coat options in the area.

I have spray painted a couple frames over the last year - it takes deligence and patience. I followed Brian's suggestions mostly - it is really labor intensive and ultimately I cut a few corners. All things considered I was pretty happy with the outcome but time will tell how they hold up.
_________________
"The path of least resistance is what makes the river crooked!” - Utah Phillips
Back to top
View user's profile Send private message Send e-mail Visit poster's website
mcrib
townie
townie


Joined: 24 Oct 2007
Posts: 232
Location: 40502

PostPosted: Thu Nov 22, 2007 10:05 pm    Post subject: Reply with quote

that bike won't Heineken green for long.
_________________
Albert Einstein trembled when he found out time was water. Seeping through the rafters to put out this burning world.
Back to top
View user's profile Send private message Send e-mail
Burch
training wheels
training wheels


Joined: 09 Nov 2007
Posts: 10

PostPosted: Fri Nov 23, 2007 12:54 am    Post subject: Reply with quote

Yeah, it was Metal Cleaners, and every one of them was a grumpy cocksucker. But it turned out awesome.
Back to top
View user's profile Send private message
brokebike
cutter
cutter


Joined: 21 Oct 2007
Posts: 2434
Location: local

PostPosted: Fri Nov 23, 2007 7:35 am    Post subject: Reply with quote

The good thing about Metal Cleaners, Drew is that you can basically walk your bike over to them... they're at the end of National Ave. I've had two bike frames powdercoated there (my current polo bike, and another old Schwinn that you guys probably haven't seen because it has been laying around in parts in my garage).

I can confirm that they are kinda hard to deal with. They just make you feel like they don't really want to mess with your job, and they seem to raise their prices arbitrarily depending on their mood.

No matter who you go with, keep in mind that powder coating isn't as exact as painting... meaning, it is harder for them to mask off certain areas, like fork crowns and bottom bracket shells - this means that you will likely have to take a Dremel tool or a wire brush to get the polyester coating cleaned out of areas where things need to be threaded, or have an exact fit... so even when finished, you'll need to do a bit of work before you can get it all back together again.

or, you could take it to a bike shop and have them do all of the facing and reaming for you.
Back to top
View user's profile Send private message
mcrib
townie
townie


Joined: 24 Oct 2007
Posts: 232
Location: 40502

PostPosted: Fri Nov 23, 2007 9:43 am    Post subject: Reply with quote

guess we are leaning towards painting it ourselves. I think the conclusion I have reached is no matter how you go about it it's gonna be a pain in the ass. Thanks for all the advice.
_________________
Albert Einstein trembled when he found out time was water. Seeping through the rafters to put out this burning world.
Back to top
View user's profile Send private message Send e-mail
jkizzle
cutter
cutter


Joined: 29 Oct 2007
Posts: 519
Location: I.L.L.

PostPosted: Fri Nov 23, 2007 10:59 am    Post subject: Reply with quote

check on www.bikeforums.com they have alot of info on there in old threads about doing it.


im pretty sure you have to get through the clearcoat and then scuff up the paint pretty good. then you prime it, repaint it, and recoat it.

if its carbon be really careful, that stuff can really get messed up by sanding it...
Back to top
View user's profile Send private message AIM Address
sailorjames
cutter
cutter


Joined: 15 Nov 2007
Posts: 329

PostPosted: Fri Nov 23, 2007 5:59 pm    Post subject: Reply with quote

I've painted one bike frame and the whole process is something i've taken great interest in during the past few months. My first frame turned out ok, but the job was rushed and it shows.

Out of the stuff I've read I would say the best step by step process i've seen, if you have the time is that of
Joe Bell.

Also, if you're on a steel bike, you'll want to consider that the paint on the dropouts is going to get scratched up from your axle nuts and that will open up a place for rust to start. I've been thinking of getting my dropouts metal plated on my next frame, anyone know where that would be done at and what an approximate cost would be for nickel/chrome?
Back to top
View user's profile Send private message
DHB
hipster
hipster


Joined: 28 Oct 2007
Posts: 71
Location: I'm not here, I'm over there.

PostPosted: Fri Nov 23, 2007 11:22 pm    Post subject: Reply with quote

I'm not sure how durable most spray paint clear coats are, so you might want to try an automotive enamel instead, which you could probably get at most auto parts stores.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
brokebike
cutter
cutter


Joined: 21 Oct 2007
Posts: 2434
Location: local

PostPosted: Sat Nov 24, 2007 7:49 am    Post subject: Reply with quote

sailorjames wrote:
Also, if you're on a steel bike, you'll want to consider that the paint on the dropouts is going to get scratched up from your axle nuts and that will open up a place for rust to start.


...another good reason for keeping the original paint on the bike frame and just painting over it. Whatever bike it is, most likely that original paint is on there pretty good, and no matter how good your spraypaint job is, the paint is going to chip like crazy on your dropouts.

Auto paints and industrial paints have nasty hardeners in them that regular rattle-can paints do not, which is why they are so durable, and chip resistant. You could put 10 coats of rattle-can clear coat on a frame, and it's still going to chip the first time you hit your U-lock against it... just something you have to learn to live with.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    LexRides Forum Index -> Mechanical Questions All times are GMT - 6 Hours
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group